Hydrel IGF4 BR LED P1 80CRI 30K MVOLT 15DEG 5T FLC 34B ZT 4" In-Grade LED Light, Brass Door, P1 Performance Package, 80 CRI, 3000K, 120-277V, 15 Degrees Distribution, 5 Degrees Tilt, Flat Lens Clear, 3/4" NPT Bottom, 0-10V Dimming

Home > Hydrel Lighting > Hydrel In-Grade > Hydrel IGF4 >

Alternative Views:

Our Price: $1,568.16

Usually Ships in 3-5 business days. Urgent Project? Contact Us.

Model: HYDREL-IGF4-110891

Qty:

Technical Spec

Downloads

Technical Spec

PRODUCT FAMILY SPECIFICATIONS
INTENDED USE: The IGF4 LED ingrade Series is intended to provide years of trouble free operation for even the most severe direct burial applications. It utilizes a modular design to provide fast and simple installation along with easy to replace LED and driver modules if needed in future years for both maintenance and product efficiency gains. This product is ideal for all uplighting applications up to 1,100 lumens where a small footprint ingrade is desired.

DOOR MATERIAL: Aluminum Door: Aluminum die cast material, alloy 380 with clear coat standard. Available with optional painted finish. Brass Door: Brushed, corrosion resistant, alloy 385 brass material. Stainless Steel Door: Brushed, corrosion resistant, alloy 304 stainless steel material.

ROUGH-IN SECTION: The robust polymer Rough-In section is molded from a U.V. stabilized material that is both impact and corrosion resistant for all types of environments. The rough-in utilizes a integral junction box to support easy access and initial installation.

CONDUIT ENTRIES: 34B 3/4" NPT Bottom (includes 2 3/4" bottom) 34S 3/4" NPT Side (includes 2 3/4" one on each side 180° apart)

FINISHING SECTION: The finishing section includes a standard die cast aluminum face plate with a corrosion resistant finish. Upgraded face plates are available in highly corrosion resistant stainless steel and brass with brushed finishes. Oversized trim face plate to trim out the finished installation hole for tile and other surface materials

LED MODULE: The LED module utilizes a highly corrosive resistant die cast brass housing. The module accomplishes a dual purpose of water ingress and thermal management to protect the critical LED components and ensure years of serviceable life. Double sealed from the environment utilizing a moisture blocking fitting and silicone seals are trademark to Hydrel quality.

OPTICS: 15DEG, 30DEG, 60DEG, 90DEG Wall Wash, 30VX70H and 70VX30H

VOLTAGE: 12 volt (only available with P1) and MVOLT 120-277 Volt 50/60HZ

LENS: Tempered Borosilicate Glass

LIGHT ENGINE: The light engine includes the highest output LEDs available coupled with a precision optic and light shaping films to provide the most efficient beams delivering light onto the intended surface. All within 3 MacAdam ellipses.

POWER MODULE: The LED driver is fully encapsulated within the die cast brass driver module housing. The thermally conductive epoxy material provides not only thermal dissipation of the driver for optimum operation but also the highest level of water ingress protection for this critical component.

ELECTRICAL: MVOLT (120-277) 50/60 Hz LED power supply. Class 2 electronic driver has a power factor >90%, THD <20%, and has an expected life of 100,000 hours with <1% failure rate. 6 kv Surge protection meets a minimum Category C Low operation (per ANSI/IEEE C62.41.2).

LISTING: cCSAus, suitable for wet locations, laboratory tests conducted by CSA to UL Standard UL-1598 and UL-8750.

GOVERNMENT PROCUREMENT:
BAA -- Buy America(n) Act: Product qualifies as a domestic end product under the Buy American Act as implemented in the FAR and DFARS. Product also qualifies as manufactured in the United States under DOT Buy America regulations.
BABA -- Build America Buy America: Product qualifies as produced in the United States under the definitions of the Build America, Buy America Act.

WARRANTY: 5-year limited warranty

Share your knowledge of this product. Be the first to write a review »

Browse for more products in the same category as this item:

Hydrel Lighting > Hydrel In-Grade > Hydrel IGF4